Gridfinity 3×3×6 bin
125.5 × 125.5 mm outside, 45.5 mm tall with the stacking lip. One open compartment of 123 × 123 × 33.8 mm (about 511 ml). Free STL, generated to the Gridfinity spec.
- Outer footprint
- 125.5 × 125.5 mm
- Height (with lip)
- 45.5 mm
- Inside (compartment)
- 123 × 123 mm
- Usable depth
- 33.8 mm
- Print time (P1S, 0.2 mm)
- 2 h 02 min
- PLA used
- 82.7 g · 27.74 m
- Watertight STL
- Yes, checked
- File
- 0.21 MB
Includes the label tab (36°, 15.85 mm), the finger scoop, the 0.95 mm wall and the standard stacking lip. No magnet holes in this file, so it prints without supports; add 6 × 2 mm magnet or M3 screw holes in the customizer.
What fits in a 3×3×6
Counted lying flat in one layer, below the stacking lip, so bins still stack. Real parts vary, so allow a little slack.
| Item | Size (mm) | Fits |
|---|---|---|
| AAA battery | 44.5 × 10.5 × 10.5 | 22 pcs |
| AA battery | 50.5 × 14.5 × 14.5 | 16 pcs |
| 18650 cell | 65.2 × 18.6 × 18.6 | 6 pcs |
| 9 V battery | 48.5 × 26.5 × 17.5 | 8 pcs |
| CR2032 coin cell | 20 × 20 × 3.2 | 36 pcs |
| SD card | 32 × 24 × 2.1 | 15 pcs |
| 1/4 in hex bit (25 mm) | 25 × 7.2 × 7.2 | 68 pcs |
| LEGO 2×4 brick | 31.8 × 15.8 × 11.4 | 21 pcs |
| Credit card | 85.6 × 54 × 0.8 | 2 pcs |
| Arduino Uno | 68.6 × 53.4 × 15 | 2 pcs |
| Raspberry Pi 4 | 85.6 × 56.5 × 17 | 2 pcs |
| Sticky-note pad 76 mm | 76 × 76 × 10 | 1 pc |
| Golf ball | 42.7 × 42.7 × 42.7 | no |
| Index card 3×5 in | 127 × 76.2 × 0.3 | no |
| Fine-tip marker | 140 × 16 × 16 | no |
| Pencil (unsharpened) | 190 × 7.5 × 7.5 | no |
Need smaller pockets? Split it into compartments in the customizer.
Questions
What are the exact dimensions of a Gridfinity 3×3×6 bin?
Outside it is 125.5 × 125.5 mm (3 and 3 grid cells of 42 mm, minus 0.5 mm clearance) and 45.5 mm tall including the stacking lip. The body is 6 × 7 = 42 mm; the lip adds 3.5 mm. The open compartment is 123 × 123 mm and 33.8 mm deep below the lip.
How tall a drawer do I need?
On a standard 5 mm baseplate the bin's top is 50.5 mm above the drawer floor, so you need at least 52 mm of clear height. Without a baseplate (bin straight on the drawer bottom, feet only) it needs 47 mm.
How many fit on a 4×4 baseplate?
1 of them, in the 3×3 orientation. A 4×4 baseplate is 168 × 168 mm.
How long does it take to print?
2 h 02 min and 82.7 g (27.74 m) of PLA, measured by slicing this exact STL in OrcaSlicer with Bambu Lab P1S profiles: 0.4 mm nozzle, 0.2 mm layers, 228 layers, no supports. Other printers and profiles will differ.